Varimixer W20 F Istruzioni per gli Interventi Scaricare il pdf

Varimixer

BEAR

Varimixer

BEAR

Varimixer

BEAR

654

789

MAX

342

MIN

Varimixer

072003 (012010)

BEAR VARIMIXER

OPERATING INSTRUCTIONS

RN20 MK-I

MACHINE NO.:

ORDER NO.: 00011 Original manual

Place the bowl in the bowl arms.

Ensure that the bowl is placed correctly.

Place the mixing tool in the bayonet shaft.

The pin of the tool must be turned into the

bayonet hole.

Raise the bowl to working position by

pulling the handle forward. Ensure that

the bowl is placed correctly while the

bowl is lifted.

Push the speed selector lever to obtain

the required speed.

The speed must be changed only

when the mixer is running.

If the mixer is equipped with a timer, set

the time required, by turning the timer to

the right. The mixer will stop automati-

cally, when the time runs out. Set the

timer on HOLD when not used; otherwise

the mixer will not start.

Recommended maximum speeds.

Before the mixer is stopped, the speed

selector lever should be moved to the

lowest speed.

The mixer must not be started

when loaded in high speed position.

Stop the mixer by pressing the red stop

button > STOP <

OVERLOADING: Take care not to overload the mixer. Tough and heavy doughs might reduce the working capacity of the mixer by 75%. The

capacity will be further reduced if the speed of the tool is increased beyond what is recommended, or if a wrong tool is used. Big lumps

of grease or cooled ingredients must be divided into fine particles before placed into the bowl. A long period of overloading will make the

thermal overload relay stop the mixer. Let the mixer rest for approx. 3 minutes, and press the red stop button

before pressing the green

start button.

If the mixer is stopped in high speed when loaded, the bowl is to be removed from the mixer and the speed set to low speed before the

bowl is placed in the mixer again.

To the attachment drive should only be connected attachments produced by A/S WODSCHOW & CO.

The mixer is meant for producing masses and doughs which will not release reactions or liberate material which can harm the user.

WARNING: It can cause bodily harm if you stick your hands into the bowl while the mixer is running.

Regarding installation, cleaning and maintenance, se back page.

Start the mixer by pressing the green

start button > START <

The mixer must only be started when

the bowl is in working position, and

safety guard, if mounted, is closed.

1 2 3 4 5 6 ... 11 12

Sommario

Pagina 1 - RN20 MK-I

VarimixerI0BEARVarimixerI0BEARVarimixerI0BEAR65478923MAX53421MIN1VarimixerI0072003 (012010)BEAR VARIMIXEROPERATING INSTRUCTIONSRN20 MK-IMACHINE NO.:GB

Pagina 2 - SERVICE INSTRUCTIONS

InnehålliEG‐försäkranommaskinensöverensstämmelse,(Maskindirektivet2006/42/EG,bilaga2,A) SEContenutodelladichiarazioneCEdiconformitàp

Pagina 3

Pagina 4

20A/S WODSCHOW & CO.Industrisvinget 6DK-2605 BrøndbyDenmarkPhone: 43 44 22 88Telefax: 43 43 12 [email protected] www.bearvarimixer.com

Pagina 5 - ADJUSTMENT OF SPEED:

23610459741224017161942821120184443255SERVICE INSTRUCTIONSBEFORE REPAIR, THE MIXER MUST BE DISCONNECTED.

Pagina 6 - ADJUSTING OF BOWL HEIGHT:

3182223(1) Remove the top cover of the mixer (1) and the plastic cover (43) by removing the 2 screws (2).(3) The attachment engagement hub is taken ou

Pagina 7 - WIRING DIAGRAMS:

412412113873263130342628373525383315362927(24) The planetary head is taken off in the following way:a) The top cover of the mixer (1), the attachment

Pagina 8

5393215347835169BC111513143812Mounting of the planetary head should be done in reverse order.When the lower fork (15) and the spring (34) are moun

Pagina 9

6454752565350465154D49484550171820195845(45) Bowl arms are to be exchanged in the following way:a) Disconnect the mixer on the main switch or disconne

Pagina 10

7WIRING DIAGRAMS:Connection: 1 phase + 0 + earth, or 2 phases + earth.Control voltage to relay: 1 phase + 0, or 2 phases.Connection: 3 phases+ 0 + ear

Pagina 11

8A/S WODSCHOW & CO.Industrisvinget 6. DK-2605 BrøndbyDenmarkPhone: 43 44 22 88Telefax: 43 43 12 80www.wodschow.dkINSTALLATION - CLEANING -

Pagina 12 - A/S WODSCHOW & CO

IndholdafCEOverensstemmelseserklæring,(Maskindirektivet,2006/42/EC,BilagII,delA) DKContentsoftheECDeclarationofconformityformachin